Injection:Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. During melt kneading, the temperature of the melted resin measured by a thermocouple at a die zone of the extruder was 260 to 270° C. The obtained pellets were dried at 120° C. for 5 hours and subjected to an injection molding using an injection molding machine (Autoshot 50D from Fanuc Ltd.) for the following tests. (1) Measurement of Flexural Modulus A plaque with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C., and the flexural modulus was measured in accordance with ASTM D790. ..
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance Evaluation of a Molded Article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate. .. Surface appearance thereof was evaluated by visual observation and classified by the following criteria: ◯: good appearance X: silver generation was observed (6) Content of Agglomeration of Component (B) and/or Component (C) A plate with size of 50 mm (W)×90 mm (L)×2.5 mm (T) was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 290° C. and mold temperature of 80° C. The content of agglomeration of component (B) and/or component (C) on the front and back surfaces of 4 plates was counted by the following standards. ..
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis Resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance Evaluation of a Molded Article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate. .. Surface appearance thereof was evaluated by visual observation and classified by the following criteria: ◯: good appearance X: silver generation was observed (6) Content of Agglomeration of Component (B) and/or Component (C) A plate with size of 50 mm (W)×90 mm (L)×2.5 mm (T) was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 290° C. and mold temperature of 80° C. The content of agglomeration of component (B) and/or component (C) on the front and back surfaces of 4 plates was counted by the following standards.
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis Resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance Evaluation of a Molded Article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate.
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance evaluation of a molded article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate. .. Surface appearance thereof was evaluated by visual observation and classified by the following criteria: ◯: good appearance X: silver generation was observed (6) Content of agglomeration of component (B) and/or component (C) A plate with size of 50 mm (W)×90 mm (L)×2.5 mm (T) was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 290° C. and mold temperature of 80° C. The content of agglomeration of component (B) and/or component (C) on the front and back surfaces of 4 plates was counted by the following standards.
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. During melt kneading, the temperature of the melted resin measured by a thermocouple at a die zone of the extruder was 260 to 270° C. The obtained pellets were dried at 120° C. for 5 hours and subjected to an injection molding using an injection molding machine (Autoshot 50D from Fanuc Ltd.) for the following tests. (1) Measurement of flexural modulus A plaque with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C., and the flexural modulus was measured in accordance with ASTM D790. ..
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance evaluation of a molded article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate. .. Surface appearance thereof was evaluated by visual observation and classified by the following criteria: ◯: good appearance X: silver generation was observed (6) Content of agglomeration of component (B) and/or component (C) A plate with size of 50 mm (W)×90 mm (L)×2.5 mm (T) was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 290° C. and mold temperature of 80° C. The content of agglomeration of component (B) and/or component (C) on the front and back surfaces of 4 plates was counted by the following standards. ..
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance evaluation of a molded article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate.
Stripping Membranes:Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis Resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance Evaluation of a Molded Article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate.
Article Title: Aromatic polycarbonate resin composition and production method thereof
Article Snippet: .. After residence of a resin composition in a cylinder of the injection molding machine for 20 minutes a strip specimen with thickness of 1⁄8 inch was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder set temperature of 300° C. The melt index value was measured on a sample cut out of the strip specimen obtained, in accordance with JIS-K7210 under the conditions of furnace temperature of 300° C. and load of 1.2 kg. (Unit: g/10 minutes) (4) Thermal-hydrolysis resistance A test piece for a tensile test was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.) set at cylinder temperature of 280° C. and mold temperature of 80° C. The test piece was exposed to an environment of 80° C. and relative humidity of 95%, and the tensile break strength was measured in accordance with ASTM-D638. .. The time required for the tensile break strength to decrease to 1⁄2 of the initial value (before exposure) was measured. (Unit: hour) (5) Appearance evaluation of a molded article A plate with size of 150 mm×150 mm×2 mm was molded using an injection molding machine (Autoshot 50D of Fanuc Ltd.), set at cylinder temperature of 320° C. and mold temperature of 80° C., by filling into a mold cavity from one point gate with diameter of 1.6 mm at one end of the plate.
|
